 |
 |
LIST | 100-Series | 200-Series |
300-Series | 400-Series
| 500-Series |
600-Series | 700-Series |
800-Series |
Floating Fountains
| Replacement Parts |
|
|
|
| « Back To 400-Series | Your Shopping Cart |
|
|
|
|
492-Series Wind Compensation System
The primary function of the HOBBS 492-Series Wind Compensation System is to reduce or eliminate water loss due to the spray blown from the pool. This is achieved by reducing the height of the spray and/or turning the pump off. HOBBS 492-Series wind compensation system panels are solid state and provide an L.E.D. digital readout of the actual wind velocity in miles per hour (mph). The panel has two stages, each with dial-adjustable wind velocity actuation points, “auto-off-manual” function switch and a “high wind” pilot light to indicate stage actuation. The wind compensation system panel is available in two versions: (1) Pre-mounted in a clear cover, carbonate and phenolic resin enclosure (HOBBS #492-13), or (2) a panel/door mount (HOBBS #492-14) typically used in conjunction with a HOBBS Custom Control Panel. Stage one is generally used to reduce the water effect height in moderate wind conditions, and stage two is used to deactivate the fountain pump in high wind conditions. The sets of internal switches for the two stages are identical, but independent of each other; therefore, just one stage may be used with the other remaining as an alternate. There is a delay circuit built into the unit to read the wind speed after a stage is activated ( 90 seconds for the first stage and from 30 - 350 seconds for the second stage). If the wind velocity drops and stays below the setting on the dial for the designated reading interval, the stage will deactivate, allowing the fountain to resume normal operation. If the wind velocity stays above, or drops below then again exceeds the velocity setting during the full reading interval, the stage will remain activated and another reading interval will start. Consult a HOBBS Sales Engineer or Project Engineer if further assistance is needed in integrating the wind compensation system with the fountain. |
|
|
|
|
|
|
|
|
|
| #492-13 Wind Compensation Panel |
$ |
1375.00 |
|
| Solid state; three-digit LED readout of wind speed in MPH; input terminals for one, two or three anemometers, with an LED pilot for each to indicate rotation status; three interior troubleshooting LEDs for anemometer operational status; two independent Stages, each with dial-adjustable wind velocity actuation point (up to 25 MPH), "Auto-Off-Manual" function switch, and a "high wind" LED pilot to indicate stage actuation status; Stage 1 has a fixed 90-second delay in deactuation time; and Stage 2 has a set screw-variable 30- to 300- second delay in deactuation time; each stage has an output relay with one normally open and one normally closed set of contacts; each rated at 10 Amps at 240 Volts AC; input power range is 100 to 250 Volts AC at 50/60 Hertz; side-hinged PVC front faceplate permits easy access to the internal, coded, screw clamp terminal strip, housed in a NEMA 4 UL-listed gray polycarbonate enclosure with clear polycarbonate cover; and 1/2" and 3/4" knockouts for conduit connection. (Note: Specify HOBBS #492-22 Anemometer separately). |
|
| #492-14 Wind Compensation Panel - Panel / Door Mount |
$ |
1375.00 |
|
| Solid state; three-digit LED readout of wind speed in MPH; input terminals for one, two or three anemometers, with an LED pilot for each to indicate rotation status; three interior troubleshooting LEDs for anemometer operational status; two independent stages, each with dial-adjustable wind velocity actuation point (up to 25 MPH), "Auto-Off-Manual" function switch, and a "high wind" LED pilot to indicate stage actuation status; Stage 1 has a fixed 90-second delay in deactuation time, and Stage 2 has a set screw-variable 30- to 300- second delay in deactuation time; each stage has an output relay with one normally open and one normally closed set of contacts; each rated at 10 Amps at 240 Volts AC; input power range is 100 to 250 Volts AC at 50/60 Hz; the electonics and a coded, screw clamp terminal strip are attached to the back side of the PVC faceplate which is screw-mounted to an opening in the door of the main fountain control panel; mounted over and around the faceplate, with an O-ring for a watertight seal, is a NEMA 4, gasketed, hinged inspection window with a light gray polycarbonate frame and a transparent smoked polycarbonate cover; door-mounted terminal strip is prewired to the main control panel's terminal strip. (Note: Specify #492-22 Anemometer separately). |
|
| #492-22 Anemometer |
$ |
85.00
|
|
| Balanced, one-piece, three-cup lexan rotating assembly; sine wave 9 volts RMS AC (alternating current) generator, with lexan and PVC sealed body; corrosion resistant bearings and shaft; 1/2" F.N.P.T. Connection; with 12" of #18/2 cable. (Note: Shielded cable required to complete installation). |
|
|
